Skip to main content Skip to search Skip to main navigation
Your partner for trades, industry, and commercial customers
Visit us Online!
Go to homepage

Guides · Sommer twist M

Sommer twist M troubleshooting and LED indicators

Search by LED or symptom, including SH, Safety, remote control and gate movement.

Work on the control, operator and safety devices must be carried out by qualified personnel. Isolate the supply and secure against restarting before work. Follow the manufacturer’s instructions, including battery isolation and capacitor discharge times where applicable. Stop using a system with faulty safety devices or uncontrolled movement.

Use the manual for your exact control version. The following guidance helps to identify the affected area before a professional inspection. Manufacturer manual (PDF)

Last updated: November 2026 · torautomation24 editorial team · Based on the official manufacturer manual · Installation manual (PDF)

Control LEDs

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
Netz LED offSupply may be missingHave the incoming supply, fuses and voltage during starting checked by an electrician.—
SH flashing rapidlyStored values may be invalid or jumper changed after learningRecord whether a power failure or jumper change preceded the fault. A specialist should determine whether reset and new learning runs are needed.—
Netz + Safety onPhotocell beam may be interruptedCheck the travel area from a safe position. With the system stopped, check for dirty or obstructed optics. Have alignment, wiring and function checked if the fault persists.—
Netz + AUF/ZU onA command device may supply a continuous signalCheck whether another command device works. Have the push button, contacts and cable checked.—
Receiver LED does not respondRadio signal not received or receiver not workingCheck the battery and compare with a second learned transmitter. Have the antenna and receiver checked if range remains poor.—

Remote controls and push buttons

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
Transmitter LED offBattery flat, incorrectly inserted or transmitter faultyCheck battery type, polarity and condition. If a new battery does not help, have the transmitter checked.—
Short range onlyWeak battery or poor receptionCheck the battery and compare with a second learned transmitter. Have the antenna and receiver checked if range remains poor.—
Button works, transmitter does notTransmitter unlearned or incompatible radio systemHave operating mode, configuration and commissioning checked against the manual.—
Pedestrian opening does not respondPartial-opening transmitter button may not be learnedHave operating mode, configuration and commissioning checked against the manual.—
Key switch does not respondContact, switch or wiring faultyCheck whether another command device works. Have the push button, contacts and cable checked.—

Gate movement

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
Gate does not openDrive released, gate obstructed, frozen or electric lock engagedCheck for visible obstructions, ice, snow and an unreleased lock. If the motor hums without movement, switch the system off immediately.—
Gate does not closePhotocell, supply or radio faultCheck the travel area from a safe position. With the system stopped, check for dirty or obstructed optics. Have alignment, wiring and function checked if the fault persists.—
Gate stops and reversesObstacle detection, safety edge, photocell, wind or stiff hingesHave the door checked for stiffness, blockages, spring damage, imbalance and wind load before altering force settings.—
Gate does not reach limit positionLimit switch or mounting bracket incorrectly setHave A/B mounting dimensions, brackets and limit-switch settings checked against the installation manual.—
Uneven gate movementMounting dimensions may differHave A/B mounting dimensions, brackets and limit-switch settings checked against the installation manual.—
Operator hits pillarMounting dimensions or limit position incorrectHave A/B mounting dimensions, brackets and limit-switch settings checked against the installation manual.—
Incorrect closing sequenceLeaf operator assignment may be incorrectHave active and passive leaf assignment checked against the wiring diagram.—
Gate does not stop at obstacleLearning mode or unsuitable force settingsTake the system out of service. Have force limitation and safety devices tested by a qualified technician.—
Force values not learnedControl may not be prepared for learning runHave operating mode, configuration and commissioning checked against the manual.—

Fault memory and restart

Record which LEDs are lit or flashing and whether the fault followed a power failure, jumper change or learning run. A reset may require new force-learning runs and a professional safety check. Follow the commissioning chapter for the exact variant.

Frequently asked questions

Does a fault code identify a defective part?

It identifies the affected function or circuit. Wiring, adjustment, supply and mechanics can cause similar messages. Have the cause checked before replacing a component.

Which information should I send with a compatibility enquiry?

Send the rating plate, control part number, supply voltage, software version where available and the full fault message. For radio issues, include transmitter and receiver details.

Can I acknowledge or reset a fault immediately?

Resolve the cause first. Reset procedures and learning runs vary by model, and a factory reset may erase settings. Follow the manual for the installed version.

All guides · Ask about compatibility

Skip product gallery

Controls and compatible spare parts

Sommer Twist M swing gate operator up to 300kg single-leaf set
€425.00*
plus VAT

in stock

Sommer Twist M S3 swing gate operator up to 300kg double-leaf set
€549.00*
plus VAT

in stock