Skip to main content Skip to search Skip to main navigation
Your partner for trades, industry, and commercial customers
Visit us Online!
Go to homepage

Guides · GfA TS 971

GfA TS 971 error codes and troubleshooting

Enter the displayed F code to find its meaning and the next checks for a qualified technician.

Work on the control, operator and safety devices must be carried out by qualified personnel. Isolate the supply and secure against restarting before work. Follow the manufacturer’s instructions, including battery isolation and capacitor discharge times where applicable. Stop using a system with faulty safety devices or uncontrolled movement.

Use the manual for your exact control version. The following guidance helps to identify the affected area before a professional inspection. Manufacturer manual (PDF)

Last updated: November 2026 · torautomation24 editorial team · Based on the official manufacturer manual

Safety circuit

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
F 1.2Slack-rope or wicket-door contact openHave the connection cable, coiled cable or WSD module, door junction-box DIP switches and both contacts checked. Check for slack suspension cables.Buy ›
F 1.3Safety circuit open, manual operation, motor thermal protection or restart protection activeCheck for overload and allow the drive to cool. Have manual operation, contacts and connectors checked. With an integrated safety brake, do not release a blockage that may indicate the brake has caught.—
F 1.4Emergency-stop button activatedCheck the emergency-stop device and have the cable checked for interruption. Emergency operation is unavailable for F 1.3 and F 1.4.—
F 1.6WSD radio transmission disturbedHave radio-channel assignment, obstacles, moisture and battery voltage checked. The manual uses P 9.6 for diagnosis and P 2.0 for channel assignment. Replace batteries below 3.2 V.Buy ›
F 1.7Wicket-door or slack-rope contact faultyHave the wicket-door contact, switching gap below 4 mm, DIP switches and coiled cable checked. Check the control supply for overload.—
F 1.8Cross-circuit in wicket-door or slack-rope circuitHave the junction-box DIP switches, series-connected 5K0 resistor and coiled-cable wiring checked.—
F 1.9WSD batteries below 3.2 VIdentify the unit and battery type. Replace batteries according to the relevant unit manual; for WSD, also check for battery passivation.Buy ›

Safety devices

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
F 2.0No safety edge detectedHave the safety edge, coiled cable, connectors, water ingress and configured sensor type checked.View selection ›
F 2.1Photocell activatedCheck the travel area from a safe position. With the system stopped, check for dirty or obstructed optics. Have alignment, wiring and function checked if the fault persists.View selection ›
F 2.2Maximum safety-edge reversals reached during automatic closingRemove obstacles safely and have closing movement and safety-edge operation checked. A specialist can review P 2.5 after finding the cause.—
F 2.48k2 safety edge activatedHave the safety edge, coiled cable, connectors, water ingress and configured sensor type checked.View selection ›
F 2.58k2 safety-edge circuit interruptedHave the safety edge, coiled cable, connectors, water ingress and configured sensor type checked.View selection ›
F 2.61k2 pneumatic safety edge activatedHave the pressure-wave switch, its sensitivity, coiled cable, terminals and safety-edge condition checked.View selection ›
F 2.71k2 safety edge faultyHave the pressure-wave switch, its sensitivity, coiled cable, terminals and safety-edge condition checked.View selection ›
F 2.81k2 safety-edge test failedHave the pre-limit switch, pressure-wave switch and edge profile checked. Verify that the edge is compressed at the closed limit position.View selection ›
F 2.9Optical safety edge activated or faultyHave the safety edge, coiled cable, connectors, water ingress and configured sensor type checked.View selection ›

Limit switches

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
F 3.1Manual-operation contact, thermal contact, emergency limit or limit-system faultCheck for overload and allow the drive to cool. Have manual operation, contacts and connectors checked. With an integrated safety brake, do not release a blockage that may indicate the brake has caught.—
F 3.2Closing emergency-limit range reachedHave the manual-operation position and drive overrun checked before restoring the door to its permitted range.—
F 3.4Pre-limit switch S5 absent, incorrectly wired or faultyHave the limit-switch system, wiring, reference and stored end positions checked against the installation manual.—
F 3.5No limit switch detected during commissioningHave the limit-switch system, wiring, reference and stored end positions checked against the installation manual.Buy ›
F 3.6Changed from DES to NES without resetting the controlHave the change of limit-switch system confirmed. A specialist should reset and recommission the control according to the manual.—

Electronics and force monitoring

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
F 3.7Internal plausibility faultRecord the fault. Have a specialist restart the control according to the manual. Repeated faults require diagnosis and possibly replacement of the control or board.Buy ›
F 3.8Control temperature too highAllow the system to cool. Have ambient temperature, installation conditions and duty cycle checked.—
F 4.1Force monitoring activatedHave the door checked for stiffness, blockages, spring damage, imbalance and wind load before altering force settings.—
F 4.5Crash switch activated, faulty or unprogrammedHave the curtain, crash switch and P 3.4 checked. The manual permits resetting with STOP for three seconds only at the open limit position.—
F 4.6Light curtain activatedCheck the travel area from a safe position. With the system stopped, check for dirty or obstructed optics. Have alignment, wiring and function checked if the fault persists.View selection ›
F 4.7Light-curtain test failedHave the connected safety device, supply, wiring and test signal checked. Keep the system out of service if protection is faulty.View selection ›
F 5.0Controller faultRecord the fault. Have a specialist restart the control according to the manual. Repeated faults require diagnosis and possibly replacement of the control or board.Buy ›
F 5.1ROM faultRecord the fault. Have a specialist restart the control according to the manual. Repeated faults require diagnosis and possibly replacement of the control or board.Buy ›
F 5.2CPU faultRecord the fault. Have a specialist restart the control according to the manual. Repeated faults require diagnosis and possibly replacement of the control or board.Buy ›
F 5.3RAM faultRecord the fault. Have a specialist restart the control according to the manual. Repeated faults require diagnosis and possibly replacement of the control or board.Buy ›
F 5.4F 3.7 detected five consecutive timesRecord the fault. Have a specialist restart the control according to the manual. Repeated faults require diagnosis and possibly replacement of the control or board.Buy ›

Door movement

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
F 5.5Digital limit switch DES faultyHave the encoder or limit-switch cable, connectors, signal and mechanical coupling checked before replacing components.Buy ›
F 5.6Door movement faultHave mechanics, limit positions, motor phases, brake, rectifier and encoder movement checked. Review runtime P 3.3 and the inverter connection. With an integrated safety brake, do not release a blockage that may indicate a caught brake.—
F 5.7Mains phase sequence changedStop the system. Have motor direction, mains phase sequence, encoder assignment and brake operation checked by qualified personnel.—
F 5.8Unexpected movement while stationaryHave brake release, brake supply, rectifier, wear and motor connections checked. Secure the door against unintended movement.—
F 5.9Drive does not follow commanded directionHave brake release, brake supply, rectifier, wear and motor connections checked. Secure the door against unintended movement.—

Frequency inverter

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
F 6.1Closing speed too highHave the door checked for stiffness, blockages, spring damage, imbalance and wind load before altering force settings.—
F 6.2Frequency-inverter communication faultHave the encoder or limit-switch cable, connectors, signal and mechanical coupling checked before replacing components.—
F 6.3DC-link undervoltageHave mains and DC-link voltage measured during movement. A specialist can then review ramp times and speeds in P 4.1–4.9.—
F 6.4DC-link overvoltageHave mains and DC-link voltage measured during movement. A specialist can then review ramp times and speeds in P 4.1–4.9.—
F 6.5Temperature limit exceededAllow the system to cool. Have ambient temperature, installation conditions and duty cycle checked.—
F 6.6Continuous current overloadHave mechanical resistance, motor rating, motor data and load checked.—
F 6.7Brake or frequency-inverter faultHave brake release, brake supply, rectifier, wear and motor connections checked. Secure the door against unintended movement.—
F 6.9Frequency-inverter collective faultRecord the fault. Have a specialist restart the control according to the manual. Repeated faults require diagnosis and possibly replacement of the control or board.—

Commissioning

Code or observationMeaning / possible causeChecks and next stepsBuy spare parts
F 8.1Travel too short when setting limit positionsDuring renewed limit setting, the manual requires at least one second of movement before saving the position. A factory reset at P 9.5 erases settings and requires recommissioning.—

LED and status displays

SignalMeaning / possible cause
F. + codeFault message; look up the code above.
E. + codeCommand received: E 1.1 OPEN, E 1.2 STOP, E 1.3 CLOSE.
8.8 ↯Emergency mode active.
8.8Programming locked.
8.8. —Possible short circuit or overload of the 24 V DC supply.
c.sService-cycle threshold reached.
.Standby; no active command.

Display dark

Have the incoming voltage, external 24 V loads, wiring and water ingress checked. If the display remains dark after professional isolation of external loads, the control may require replacement.

Fault memory and restart

Programming point 9.2 shows the last six faults; consecutive repeats are stored once. Record the entries before resetting. The GfA-Stick and GfA+ app can also support diagnosis. Factory reset 9.5 erases settings and requires recommissioning.

Emergency operation can bypass safety devices and requires a qualified technician and a secured door area. With GfA F 1.3 or F 1.4, electrical movement is unavailable even in emergency mode.

Frequently asked questions

Does a fault code identify a defective part?

It identifies the affected function or circuit. Wiring, adjustment, supply and mechanics can cause similar messages. Have the cause checked before replacing a component.

Which information should I send with a compatibility enquiry?

Send the rating plate, control part number, supply voltage, software version where available and the full fault message. For radio issues, include transmitter and receiver details.

Can I acknowledge or reset a fault immediately?

Resolve the cause first. Reset procedures and learning runs vary by model, and a factory reset may erase settings. Follow the manual for the installed version.

All guides · Ask about compatibility

Skip product gallery

Controls and compatible spare parts

GfA Elektromaten Wireless Safety Device WSD-Module
€79.00*
plus VAT

in stock

Best Seller Reduced Shipping Rate
GfA Elektromaten Replacement PCB for Door Control TS 971
€269.00*
plus VAT

in stock

GfA Elektromaten digital limit switch DES 4
€135.00*
plus VAT

in stock

GfA Elektromaten GfA-Stick
€61.00*
plus VAT

in stock

Skip product gallery

Controls and compatible spare parts

GfA Elektromaten Wireless Safety Device WSD-Module
€79.00*
plus VAT

in stock

Skip product gallery

Controls and compatible spare parts

GfA Elektromaten digital limit switch DES 4
€135.00*
plus VAT

in stock

Skip product gallery

Controls and compatible spare parts

Best Seller Reduced Shipping Rate
GfA Elektromaten Replacement PCB for Door Control TS 971
€269.00*
plus VAT

in stock

Skip product gallery

Controls and compatible spare parts

GfA Elektromaten digital limit switch DES 4
€135.00*
plus VAT

in stock